How To Set Up Rexing Trailk Camera For Timelapse Recording

Rob Johnston

Editor & Article Writer for Outdoor Wilds

How To Program a Trail Photographic camera

In this guide I accept a expect at how to program a trail camera, plus the steps to have when first opening a camera straight out the box.

Right through to finally checking on the camera after its first placement at a scouting location.

Getting started

After making the initial choice on which new trail cam to get, it's ever great to finally get your hands on the box when you become abode.

Most cameras come arranged with a few extras these days. Tree straps, mounting brackets, SD cards and even a card reader in some instances.

Spend a few minutes making sure all the pieces are in the box are equally advertised, plus the instruction manual and any warranty carte are enclosed.

Check the rubber grommet seals between the battery compartment, the front end facia and control console at the dorsum to make sure the seal are in proficient lodge.

Look for any signs of damage or scratches to the PIR sensor, camera lens, plus the infrared illuminators.

Choosing The Correct Batteries

Choosing the right batteries is critical for the best performance from a trail camera.

Batteries come in iii types.

Rechargeable batteries
Alkaline metal batteries
Lithium batteries

My selection of battery is always Lithium. The reason is only, they offer the best performance to price ratio. The initial outlay is more, but they'll last far longer than alkaline batteries.

Alkaline metal batteries once they drop below l% continue to power the camera but the functioning is affected. The drib in performance is shown by lack of illumination from the LED emitters that are used to illuminate animals at night.

Rechargeable batteries may seem a good thought just most of them accept also low a voltage over time to proceed a trail camera running to maximum levels.

If you'd like to know more about batteries for trail cameras accept a look at this article I have written dedicated to the discipline.

SD Cards

SD cards are inexpensive these days. The majority of trail cams piece of work with sizes up to 32GB. I'd suggest a class eight or higher up, ideally class x.

The class of an SD card denotes how fast it handles data existence stored. For a full Hd trail camera, course 10 is essential. Accept a read of my commodity dedicated to SD cards.

How To Fix Your Photographic camera

With the camera checked over, batteries installed, plus a suitable SD card it's fourth dimension to take a look at all those menu settings inside the photographic camera itself.

Menu settings are accessed commonly by the colour LCD viewing screen. The viewing screen is sometimes located in the door of the camera or as in the case of Browning trail cams at the back of the camera housing.

The large advantage with the viewing screen at the back is that you tin can see what the camera lens is pointing at when setting up the camera in situ.

Camera Settings

On most trail cameras you lot'll find three main settings.

Flare-up Mode – Notwithstanding pictures
Video Mode
Fourth dimension lapse mode

Still picture mode unremarkably has the pick of setting the resolution of the picture. The bigger the moving picture size the less pictures y'all'll be able to store on the SD card.

If your planning on leaving the camera to run for say, vi months then it may be worth setting the pictures to low res.

Video mode will also have an selection to record in full HD or 720P. 720P beingness the smaller resolution. The video below will requite you an idea of what to expect when setting upward a trail camera. The camera shown here is the Browning XD Pro.

What Does Time Lapse Hateful?

Time lapse means the trail camera is set to record for a prepare duration. It may be for 24 hours a day or an hour either side of dusk or dawn.

However pictures or video are recorded in short bursts for a set duration. The 2 settings that control these parameters are duration and interval.

Allow'south say the time lapse is prepare to an interval of 5 minutes and a elapsing of 10 seconds. That means the camera will record a video clip every 5 minutes for 10 seconds.

Burst Mode

Flare-up fashion is function of the still picture settings. It simply means the camera will tape either 3, 5 or in some cases 8 pictures ane after the other when the camera is triggered.

Testing The Photographic camera Works

Now I've taken a wait at how to set up a trail photographic camera. It's fourth dimension to check that the camera works before heading out to the scouting area.

This may seem a hurting in the butt, but trust me, trail cameras whatsoever make or brand are known to sometimes accept a bad camera in their production batch.

All you need to practice is ready the camera up in the backyard and walk beyond the camera detection zone.

Wlak at effectually twenty metres away, both during the day and at night to test to see that the PIR sensor is working and the LED illumination is doing its job.

Viewing Pictures

Once you've checked the SD card on your iPhone or computer and fabricated sure the images are OK it'southward time to head on out to the woods.

If yous're unsure on how to check back the SD card take a look at my article on how to view trail camera pictures on iPhone or you may be interested in an dedicated SD card viewer.

Placing the Camera in the Best Location

Placing the camera in the correct location is the final essential stage. I'd suggest placing the camera close to a trail head, food plot or bedding area if you're scouting for game animals.

The diagram below shows y'all some of the nuts. How high to set the camera off the footing, the angle to the trail, annotation; likewise to bespeak the camera north if possible to avoid sun glare. This post looks at trail camera placement in more detail.

Securing The Photographic camera To Trees

A tree strap will come supplied with your camera. It's just a affair of wrapping the strap around the trunk of a tree and making sure any backlog strap is tucked into the strap to avert flapping.

Some trail cameras come with a mounting plate and screws for a more permanent fixing.

Checking On The Camera

Hopefully your trail has spent several weeks taking pictures in an expanse with enough of activity. It'due south worth taking spare SD cards with you lot to swap out the total SD card from the photographic camera.

Bluetooth or WiFi may be a feature worth looking at when choosing a trail camera as this allows yous to get within 30 anxiety of the camera without disturbing the surface area and leaving scent.

You'll be able to download the pictures onto your smartphone or tablet in this example.

For more than information on how to check a trail photographic camera, read my commodity dedicated to the subject.

Final Thoughts

I've covered all the essential stages from opening the box to returning to the camera location in this article.

This should help you to achieve better results with your trail camera and brand sure the camera performs as information technology was intended.

Cheers for stopping by. Drop a annotate below if you lot have whatsoever additional points you may experience be of use to newer trail cam users. Happy scouting!

Source: https://outdoorwilds.com/how-to-program-a-trail-camera/

Posted by: patelstemed1965.blogspot.com